DAW setup guides
Use Sessionwire with other DAWs
Sessionwire works with any DAW that loads VST3, AU or AAX plugins, including Reason, Ardour, Harrison Mixbus, Adobe Audition and WaveLab. The plugins don't come in VST2. If your DAW doesn't have its own guide, these rules work everywhere. Send your ...
Use Sessionwire with Mixcraft
Mixcraft uses the VST3 versions of the Sessionwire plugins on Windows. Send your project Click the FX button on the Master Track and add the Sessionwire Send plugin at the end of the chain. In your Studio, set HQ Audio Source to the Sessionwire Send ...
Use Sessionwire with Sonar (Cakewalk)
Sonar, previously Cakewalk by BandLab, uses the VST3 versions of the Sessionwire plugins on Windows. Send your mix Right-click in the FX Rack on your Master bus and add the Sessionwire Send plugin at the end. For a separate cue mix, create a bus, ...
Use Sessionwire with Digital Performer
Digital Performer uses the AU or VST3 versions of the Sessionwire plugins. Send your mix Add the Sessionwire Send plugin to the last insert on your Master Fader. For a separate cue mix, create a stereo aux fed by an unused bus, send each track to it, ...
Use Sessionwire with Bitwig Studio
Bitwig Studio uses the VST3 versions of the Sessionwire plugins. Send your mix Add the Sessionwire Send plugin at the end of the device chain on the Master track. For a separate cue mix, create an effect track, send each track to it, and put the Send ...
Use Sessionwire with Studio One and Fender Studio Pro
Studio One was renamed Fender Studio Pro in version 8. These steps work in both. It uses the VST3 versions of the Sessionwire plugins, or AU on a Mac. Send your mix Add the Sessionwire Send plugin to the last insert slot on the Main Out channel, at ...
Use Sessionwire with Cubase and Nuendo
Cubase and Nuendo use the VST3 versions of the Sessionwire plugins. The steps are the same in both. Send your mix In the MixConsole, add the Sessionwire Send plugin to the last insert slot on the Stereo Out output channel. For a separate cue mix, ...
Use Sessionwire with REAPER
REAPER uses the VST3 versions of the Sessionwire plugins, or AU on a Mac. Send your mix Click the FX button on the Master track and add the Sessionwire Send plugin at the end of the chain. For a separate cue mix, create a track for it, send each ...
Use Sessionwire with GarageBand
GarageBand works well for sending your music into a Session. Because it has no buses or aux tracks, recording a Guest in GarageBand is limited. Turn on Audio Units Open GarageBand > Settings > Audio/MIDI and make sure Enable Audio Units is on. ...
Use Sessionwire with LUNA
LUNA, from Universal Audio, uses the AU versions of the Sessionwire plugins on a Mac. AU plugins load by default; VST3 is off unless you turn it on in LUNA's Plug-In Manager. On Windows, LUNA uses VST3. Turn off ARM If you use an Apollo interface, ...
Use Sessionwire with FL Studio
FL Studio can be fussy with plugins from other developers, and the Sessionwire plugins need a few settings in FL's plugin wrapper to work reliably. Change them once for each Sessionwire plugin you use. Set up the plugin wrapper Insert the Sessionwire ...
Use Sessionwire with Ableton Live
Ableton Live uses the VST3 or AU versions of the Sessionwire plugins. If Live doesn't list them after you install, open Settings > Plug-Ins, check VST3 or Audio Units are turned on, and click Rescan. Send your mix Put the Sessionwire Send plugin at ...
Use Sessionwire with Logic Pro
Logic Pro uses the AU versions of the Sessionwire plugins. Check these settings first Make sure Low Latency Mode is off. It bypasses plugins to cut delay, and that includes the Send plugin, so nobody hears you. Then open Logic Pro > Settings > Audio ...
Use Sessionwire with Pro Tools
Pro Tools uses the AAX versions of the Sessionwire plugins, which the Sessionwire Audio Plugins installer adds on both Mac and Windows. Turn off Low Latency Monitoring first Low Latency Monitoring must be off. With it on, the Send plugin on your ...